Can I Set Up a Bathtub Myself? Factors to Consider As Well As Steps
Can I Set Up a Bathtub Myself? Factors to Consider As Well As Steps
Blog Article
The article below on the subject of How to Install a Bathtub: Install an Acrylic Tub and Tub Surround is definitely informative. Read it for yourself and see what you think of it.
Mounting a bath tub isn't exactly brain surgery, yet it does call for strong plumbing, woodworking, and in some cases, tiling skills. Replacing an old tub with a new one is likewise a reasonably difficult job. If the old bathtub is readily easily accessible, the task can move immediately; if you need to open a wall surface to get rid of the old tub as well as place the new tub, the job is a lot harder. In either case, the job is within a residence handyman's abilities, although you will need an assistant to vacate the old tub as well as embeded in the brand-new one. Make sure you have qualified on your own for the work and also are comfortable attempting it. Instead of working with a service provider to take control of a halfway-completed task, it is much better to take into consideration employing one before you begin. Possibilities are you may require a specialist plumber to make tube links.
This write-up will help you install a new tub in your shower room if you have actually currently acquired a brand-new bathtub and don't need to change the arrangement of your previous water supply pipelines.
Your tools and material checklist should comprise the following:
Getting ready for the Setup
First of all, the supporting framework supplied with the bath needs to be fitted (if called for) according to the supplier's guidelines. Next off, fit the taps or mixer to the bathtub. When fitting the tap block, it is important to see to it that if the faucet features a plastic washing machine, it is fitted in between the bathroom as well as the taps. On a plastic bath, it is also sensible to fit a sustaining plate under the faucets device to avoid stress on the bathtub.
Fit the flexible faucet adapters to the bottom of both taps using 2 nuts and olives (sometimes provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and after that pass the outlet via the hole in the bathroom. Use the nut provided by the maker to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the flexible overflow pipeline to the overflow electrical outlet. After that, screw the pipe to the overflow face which should be fitted inside the bathroom. Make certain you utilize all of the supplied washers.
Attach the catch to the bottom of the waste outlet on the bath tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and screw on the catch to the outlet. Connect all-time low of the overflow tube in a similar manner.The bathroom ought to currently be ready to be fitted in its last position.
Removing Old Touches
If you need to change old faucets with new ones as a part of your installment, then the first thing you must do is disconnect the water. After doing so, turn on the faucets to drain any type of water remaining in the system. The procedure of eliminating the existing faucets can be quite troublesome as a result of the restricted gain access to that is frequently the situation.
Make use of a basin wrench (crowsfoot spanner) or a faucet device to undo the nut that attaches the supply pipes to the taps. Have a towel ready for the continuing to be water that will certainly come from the pipelines. As soon as the supply pipes have actually been removed, utilize the very same tool to loosen up the nut that holds the faucets onto the bath/basin. You will require to stop the single faucets from turning during this procedure. Once the faucets have been eliminated, the holes in the bath/basin will certainly have to be cleansed of any old sealing substance.
Before going on to fit the new faucets, contrast the pipe links on the old taps to the brand-new faucets. If the old taps are longer than the brand-new faucets, after that a shank adapter is required for the brand-new faucets to fit.
Installing the Bath tub
Using the two wood boards under its feet, position the tub in the called for placement. The wooden boards are useful in uniformly spreading out the weight of the bath tub over the area of the boards rather than focusing all the weight onto 4 tiny factors.
The next goal is to make sure that the bath tub is leveled all round. This can be attained by checking the spirit level and changing the feet on the tub till the level reviews degree.
To mount taps, fit the bottom of the furthest flexible tap port to the proper supply pipe by making a compression sign up with; after that do the very same for the various other faucet.
Activate the water and also examine all joints and also new pipework for leakages and also tighten them if essential. Fill the bathtub and likewise examine the overflow electrical outlet and also the normal outlet for leaks.
Lastly, take care of the bathroom paneling as explained in the supplier's user's manual. Tiling and securing around the bath tub should wait until the bathtub has been utilized at least once as this will settle it into its final setting.
Suitable New Touches
If the tails of the brand-new faucets are plastic, after that you will certainly require a plastic port to avoid damages to the string. One end of the adapter fits on the plastic tail of the faucet and also the various other end supplies a link to the current supply pipelines.
If you require to fit a monobloc, after that you will certainly need minimizing couplers, which links the 10mm pipeline of the monobloc to the conventional 15mm supply pipe.
Next, position the tap in the mounting opening in the bath/basin making certain that the washers are in place between the faucet and also the sink. Safeguard the faucet in place with the producer offered backnut. Once the tap is firmly in position, the supply pipelines can be linked to the tails of the taps. The taps can either be connected by utilizing corrugated copper piping or with typical tap connectors. The former kind needs to be linked to the tap ends initially, tightening up just by hand. The supply pipes can later be attached to the various other end. Tighten both ends with a spanner after both ends have been attached.
Tiling Around the Bath tub
In the area where the bath meets the floor tile, it is needed to secure the accompanies a silicone rubber caulking. This is very important as the fitting can move sufficient to split a rigid seal, creating the water to pass through the wall between the bathroom as well as the tiling, leading to difficulties with wetness as well as possible leakages to the ceiling below.
You can choose from a selection of coloured sealants to assimilate your components and installations. They are offered in tubes and cartridges, and also are capable of sealing voids up to a size of 3mm (1/8 inch). If you have a larger gap to load, you can fill it with spins of soaked newspaper or soft rope. Keep in mind to always load the tub with water prior to sealing, to allow for the motion experienced when the tub remains in use. The sealer can break rather early if you do not take into account this motion prior to sealing.
Alternatively, ceramic coving or quadrant ceramic tiles can be used to border the bath or shower tray. Plastic strips of coving, which are easy to use as well as cut to dimension, are also quickly available on the marketplace. It is advisable to fit the ceramic tiles using water-resistant or water-proof sticky and also grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I discovered that entry on A Step-by-Step Guide to Installing a Bathtub while doing a lookup on the web. Sharing is nice. You never know, you might be doing someone a favor. I am grateful for your time. Visit again soon.
Schedule Estimate
Report this page